Gemracing Custom Plenums (Pics included)
-
- Gemini Master
- Posts: 885
- Joined: Wed May 25, 2005 7:45 pm
- Location: Melton,Vic.....
- Contact:
Gemracing Custom Plenums (Pics included)
Hi Guys,
Ive started doing plenums for 4c/d/e inlet manifolds..There made from mild steel and have a 4" round top with the rear plate fitted with 3x1/8 fittings..The front plate can suit either VLT/XF/VN V8 throttle body's...The cost is $350,which includes all machined surfaces.
PM me if interested.
*Throttle body not included.
Darren
Ive started doing plenums for 4c/d/e inlet manifolds..There made from mild steel and have a 4" round top with the rear plate fitted with 3x1/8 fittings..The front plate can suit either VLT/XF/VN V8 throttle body's...The cost is $350,which includes all machined surfaces.
PM me if interested.
*Throttle body not included.
Darren
Last edited by gemracing on Mon Oct 15, 2007 9:26 pm, edited 5 times in total.
Current Car.....
-G180 TX red coupe 9.20@148.6mph on a 26x8.5" tyre and no nitrous 2380lbs with driver
-G180 TX red coupe 9.20@148.6mph on a 26x8.5" tyre and no nitrous 2380lbs with driver
-
- Chatterbox
- Posts: 94
- Joined: Sun Oct 15, 2006 8:22 pm
- Location: Eastern suburbs,Vic
Re: Gemracing Custom Plenums (Pics included)
Can this be used on a G180 or do you make one for G series????????????gemracing wrote:Hi Guys,
Ive started doing plenums for 4c/d/e inlet manifolds..There made from mild steel and have a 4" round top with the rear plate fitted with 3x1/8 fittings..The front plate can suit either VLT/XF/VN V8 throttle body's...The cost is $350,which includes all machined surfaces.
*Throttle body not included.
Darren
1979 TD coupe with TG front end, SOHC G180, Single Weber carby, Lukey Extractors, ACL pistons, over sized valves, Ported and Polished head, stage 2 cam, balanced bottom end, 2.5" exhaust.
-
- Gemini Master
- Posts: 885
- Joined: Wed May 25, 2005 7:45 pm
- Location: Melton,Vic.....
- Contact:
Yes,shouldn't be a problem...83TG200 wrote:Darren, call me ignorant or stupid for not researching, but, is it possible to mount this plenum backwards on the manifold? because i wish to run a barrel cooler up the back of the engine bay.
Cheers
- Michael
Darren
Current Car.....
-G180 TX red coupe 9.20@148.6mph on a 26x8.5" tyre and no nitrous 2380lbs with driver
-G180 TX red coupe 9.20@148.6mph on a 26x8.5" tyre and no nitrous 2380lbs with driver
-
- Gemini Master
- Posts: 885
- Joined: Wed May 25, 2005 7:45 pm
- Location: Melton,Vic.....
- Contact:
Easy,the XF has it on the throttle body and you'll need to make one off one of the 4 bolts if using the VL one,its not that hard to do...MRJUCY wrote:but one problems how ya use fit accelerator cable??
Darren
Current Car.....
-G180 TX red coupe 9.20@148.6mph on a 26x8.5" tyre and no nitrous 2380lbs with driver
-G180 TX red coupe 9.20@148.6mph on a 26x8.5" tyre and no nitrous 2380lbs with driver
-
- Gemini Master
- Posts: 885
- Joined: Wed May 25, 2005 7:45 pm
- Location: Melton,Vic.....
- Contact:
This plenum fits all the Rodeo efi inlet manifolds,including the Piazza too.Ive so far made them for a few types of the EFI bottoms,and they have fit them all...DryftKult wrote:this fit's the early rodeo runners yeah? the ones with the big single instead on the i-tec setup?
Darren
Current Car.....
-G180 TX red coupe 9.20@148.6mph on a 26x8.5" tyre and no nitrous 2380lbs with driver
-G180 TX red coupe 9.20@148.6mph on a 26x8.5" tyre and no nitrous 2380lbs with driver