FX Holden Race Car Project

This Forum is here for each member to post pics of his/her other non Gemini related cars. Keep it to one thread per car.. if you get more pics etc, add them to your existing thread, DO NOT start a new one
Post Reply
User avatar
Holden202T
Regular
Posts: 492
Joined: Sun Mar 16, 2008 7:47 pm
Location: Tenambit, NSW.
Contact:

Re: FX Holden Race Car Project

Post by Holden202T »

i also purchased some new rear rims, these are 15 x 10 in, with 4 inch more dish than the rim below.
5.jpg
5.jpg (141.5 KiB) Viewed 14000 times
the rim wiht tyre on it is the 15 x 7's that i had on the gemini, and it has a 26 x 10in tyre on it.
6.jpg
6.jpg (129.91 KiB) Viewed 14000 times
with as much done as we could with the engine in it was time to remove it so i could finish off the firewall.
7.jpg
7.jpg (188.96 KiB) Viewed 13998 times
No matter what the question is, the answer is always more horsepower!!
User avatar
Holden202T
Regular
Posts: 492
Joined: Sun Mar 16, 2008 7:47 pm
Location: Tenambit, NSW.
Contact:

Re: FX Holden Race Car Project

Post by Holden202T »

With a baby fast approaching it was Marie's baby shower, she was out for the whole day pretty much so i invited dad and some brothers over, also firebug was loitering there ;) and we got the firewall pretty much sorted, its still got a few bits of welding to do and a heap of grinding but its on the home stretch.
8.JPG
8.JPG (573.08 KiB) Viewed 13996 times
9.JPG
9.JPG (591.63 KiB) Viewed 13996 times
we also got a heap of no longer needed holes filled up too.
10.JPG
10.JPG (193.2 KiB) Viewed 13996 times
No matter what the question is, the answer is always more horsepower!!
User avatar
Holden202T
Regular
Posts: 492
Joined: Sun Mar 16, 2008 7:47 pm
Location: Tenambit, NSW.
Contact:

Re: FX Holden Race Car Project

Post by Holden202T »

Just another shot of the front of the car for perspective.
11.JPG
11.JPG (250.37 KiB) Viewed 13994 times
And while dad and my brother were busy with the mig on the firewall i cracked out the tig to finish off the steering rack, it was cut and tacked together but never finished off .... till now.
12.JPG
12.JPG (280.61 KiB) Viewed 13994 times
and barely a week after the baby shower the baby decided she wasn't staying in there any longer and came to be 4 weeks early! Meet little Claire!
13.jpg
13.jpg (128.45 KiB) Viewed 13994 times
No matter what the question is, the answer is always more horsepower!!
User avatar
Holden202T
Regular
Posts: 492
Joined: Sun Mar 16, 2008 7:47 pm
Location: Tenambit, NSW.
Contact:

Re: FX Holden Race Car Project

Post by Holden202T »

it was clear Claire was born to be a racer, barely a week old and she was in her first 5 point harness (albiet not too happy!)

this was a transfer from Newcaslte hospital to Maitland (closer to home for us and no longer needed to be in intensive care at newcastle)
14.jpg
14.jpg (35.08 KiB) Viewed 13993 times
15.jpg
15.jpg (36.28 KiB) Viewed 13993 times
No matter what the question is, the answer is always more horsepower!!
User avatar
Holden202T
Regular
Posts: 492
Joined: Sun Mar 16, 2008 7:47 pm
Location: Tenambit, NSW.
Contact:

Re: FX Holden Race Car Project

Post by Holden202T »

i've been saying for a long time that i wanted a nutcert kit, so for christmas i finally got one!
16.jpg
16.jpg (279.43 KiB) Viewed 13988 times
i used it to mount some nuts in the firewall for the map sensor bracket, before the firewall was finished i just stuck my hand through the hole and put the nuts on them, so this was a real bonus!
17.jpg
17.jpg (205.86 KiB) Viewed 13988 times
19.jpg
19.jpg (118 KiB) Viewed 13988 times
i've since purchased some imperial mandrels and nuts for it so it mostly covers anything i need!
No matter what the question is, the answer is always more horsepower!!
User avatar
Holden202T
Regular
Posts: 492
Joined: Sun Mar 16, 2008 7:47 pm
Location: Tenambit, NSW.
Contact:

Re: FX Holden Race Car Project

Post by Holden202T »

despite most of summer being stinking hot dad and i got stuck into some panel work (as a slightly cooler alternative to welding)
1.jpg
1.jpg (208.16 KiB) Viewed 13987 times
dad has a technique of getting rust converter, and a piece of steel wool, rub it over the rusty panel till all the surface rust is loosened then wipe it off with a cloth, comes up mint!
2.JPG
2.JPG (218.22 KiB) Viewed 13987 times
after all this we gave it a light coat of primer.
3.JPG
3.JPG (225.05 KiB) Viewed 13987 times
No matter what the question is, the answer is always more horsepower!!
User avatar
Holden202T
Regular
Posts: 492
Joined: Sun Mar 16, 2008 7:47 pm
Location: Tenambit, NSW.
Contact:

Re: FX Holden Race Car Project

Post by Holden202T »

I also got a supercheap auto gift card for christmas so i used it to buy some seam sealer, and got stuck into testing it out on the boot!
4.JPG
4.JPG (79.73 KiB) Viewed 13986 times
it works, but its f*#cking messy s*#t!

so since this picture we have painted inside the boot with a finish product, but i dont have a picture of it.

thats about it at the moment, i have been a bit side tracked with some other projects but hoping to get back into the FX very soon. Its basically a shell on stands at the moment, and i want to finish some welds in the 4 link area, and the under floor/seat area then i can start applying some under body spray while its up on stands, then i can start to put the rear back together.

i am also working on finishing the firewall and steering so i can get the front back on the ground too.
No matter what the question is, the answer is always more horsepower!!
User avatar
Jonno
Korean Jesus
Posts: 2370
Joined: Tue Jul 25, 2006 5:28 pm
Location: Canberra. Where the Fast Geminis live
Contact:

Re: FX Holden Race Car Project

Post by Jonno »

Here's me puts one seat in and thinks i've won the lottery!

Looking good and congrats on Claire!

Good to hear everything is going well :)
If you guys are free over easter should pop down!
75 TX Coupe
GemiNats > https://www.facebook.com/GeminiNationals
Image
#TurboFamily #Geminats #Bucketship
YT: https://www.youtube.com/channel/UCPKSHb ... akJ04sOYjw
User avatar
Holden202T
Regular
Posts: 492
Joined: Sun Mar 16, 2008 7:47 pm
Location: Tenambit, NSW.
Contact:

Re: FX Holden Race Car Project

Post by Holden202T »

Jonno wrote:Here's me puts one seat in and thinks i've won the lottery!

Looking good and congrats on Claire!

Good to hear everything is going well :)
If you guys are free over easter should pop down!
to be fair that update is from approx may last year till now hehe :)
No matter what the question is, the answer is always more horsepower!!
User avatar
firebug
Regular
Posts: 456
Joined: Mon Oct 05, 2009 8:28 am
Location: Newcastle -32.872095,151.707064

Re: FX Holden Race Car Project

Post by firebug »

I like a good loiter... 8)
"Can't stop addicted to the shindig!..."
User avatar
Holden202T
Regular
Posts: 492
Joined: Sun Mar 16, 2008 7:47 pm
Location: Tenambit, NSW.
Contact:

Re: FX Holden Race Car Project

Post by Holden202T »

its been a long time coming for this diff, but i have got the money there for axles now and that was the last piece of the puzzle, so i thought i should get stuck into the diff shortening so i could work out when lengths the axles needed to be.

a friend borrowed a diff to use for working out how much to shorten his to fit into a VP so he cut shortrened and welded the ends back on, and once he was finished i got it to use for my setup which is much shorter so there was still enough left on the ends of the diff tubes.

so i spent what seemed like hours cutting all the mounts off and then grinding back what was left. i knew i needed to make it 4 inch narrower each side compared to the diff that was in the car, and i also wanted to get the yoke in the centre of the car, so i measured ten times and i think i finally got all the offsets right, i also had to take into account the approx 35mm for the weld on ends, and had to make sure they had the same depth in the ends for the bearing seats and so on and so forth.

so its finally cut at where i hope is going to be the right lengths, the plan now is to dummy it up in the car with the 4 link plates and weld on ends all tack welded on, just to make sure its actually right before i go and finalise all the welding.
IMG_1289.JPG
IMG_1289.JPG (567.93 KiB) Viewed 13854 times
these weld on ends look really nice, and for $90 i think it was, saves alot of time and effort!
IMG_1291.JPG
IMG_1291.JPG (216.96 KiB) Viewed 13854 times
No matter what the question is, the answer is always more horsepower!!
User avatar
Jonno
Korean Jesus
Posts: 2370
Joined: Tue Jul 25, 2006 5:28 pm
Location: Canberra. Where the Fast Geminis live
Contact:

Re: FX Holden Race Car Project

Post by Jonno »

That'll cut some time down.
75 TX Coupe
GemiNats > https://www.facebook.com/GeminiNationals
Image
#TurboFamily #Geminats #Bucketship
YT: https://www.youtube.com/channel/UCPKSHb ... akJ04sOYjw
User avatar
Holden202T
Regular
Posts: 492
Joined: Sun Mar 16, 2008 7:47 pm
Location: Tenambit, NSW.
Contact:

Re: FX Holden Race Car Project

Post by Holden202T »

yeah and weight, when i used to make them before i'd sleeve the tubes with another piece of tube, 200mm long, so definitely would have added a few kg's!
No matter what the question is, the answer is always more horsepower!!
User avatar
Holden202T
Regular
Posts: 492
Joined: Sun Mar 16, 2008 7:47 pm
Location: Tenambit, NSW.
Contact:

Re: FX Holden Race Car Project

Post by Holden202T »

i'll just leave this here.
IMG_1455.jpg
IMG_1455.jpg (273.74 KiB) Viewed 13753 times
No matter what the question is, the answer is always more horsepower!!
User avatar
firebug
Regular
Posts: 456
Joined: Mon Oct 05, 2009 8:28 am
Location: Newcastle -32.872095,151.707064

Re: FX Holden Race Car Project

Post by firebug »

Got dish?!
"Can't stop addicted to the shindig!..."
Post Reply